800-314-6390    Live Chat    Cart    Log-in   

International Coating Foil Adhesive Qt for Screen Printing Foil

International Coating Foil Adhesive Qt for Screen Printing Foil

International Coating Foil Adhesive Qt for Screen Printing Foil
Click to enlarge image(s)
Item Number
IC3801LFQT
Price
$29.99 Reg.
Qty


Submit a Review...
Screen Printing Foil Adhesive Quart.

Foil Adhesive is the recommended ink to use when screen printing onto a with the intent to apply a foil heat transfer. Foil Adhesive has small adhesive granular's in it that holds the screen printing foil onto the shirt.  This clear plastisol adhesive can help produce brilliant metallic foil designs on textiles. The adhesive can be printed directly onto the fabric and the foil applied to the dried adhesive. The adhesive can also be printed directly on the foil as a conventional transfer would be printed (mirror image) (WE RECOMMEND DIRECT PRINTING!). Designs made with 3801LF foil adhesive may be applied to light or dark fabrics.

Here is a short video that shows the process.

 

Application & Storage Information

RECOMMENDED FABRICS: 100% Cotton and some cotton/polyester blends.

ADHESIVE APPLICATION: The 3801LF Foil Adhesive should be printed right out of the container without any modifications. Stir adhesive prior to use.

SCREEN MESH AND EMULSION: 60-110 Mesh (86 Optimal) Any direct or indirect lacquer proof emulsion.
Recommend: 86 to 110 t/in or 34-43 t/cm mesh for T-Shirts
Recommend: 74 to 86 t/in or 30-34 t/cm mesh for sweatshirts

SQUEEGEE: 70 Durometer: Sharp or beveled edge

CURE TEMPERATURE:
For direct printed fabrics: 325F (163C) entire ink film.
For transfer printing (adhesive on foil): 240F to 275F (116C to 135C)
Test dryer temperatures and wash test printed product before and
during a production run.

CLEAN-UP: environmentally friendly plastisol screen wash.

PRODUCT PACKAGING Quart, 1 Gallon or 5 Gallon Containers.

STORAGE OF INK Recommend storage at 65F to 90F (18C to 32C). Avoid storage in direct sunlight. Keep containers well sealed.


FOIL APPLICATION INSTRUCTIONS:
Foil is applied colored side up and aluminum looking (dull) side down. Rub foil with eraser immediately after application to help remove any wrinkles. Allow transfer to cool completely (20 to 30 seconds) after application before removal of foil sheet. Pull foil sheet off slowly. It can be helpful to tint the 3801LF Foil Adhesive, to the color of the foil being applied, with a small amount of conventional plastisol. This process will help to keep small pinholes in the applied foil film from being noticeable. As example: Use a few grams of yellow or gold plastisol in the 3801LF Adhesive when using gold foil. Use a few grams of black or gray plastisol in the 3801LF Adhesive when using silver foil.
APPLICATION TEMPERATURE
300F to 325F (149C to 163C). Try lower temperature first for best results.
APPLICATION TIME
10-15 Seconds
APPLICATION PRESSURE
T-Shirts = Medium (40lbs.)
Sweatshirts = Medium to Heavy (40lbs. to 60lbs)
The brightest foil effect will result when the foil is first removed. To achieve a textured matte finish foil, re-seal the garment or hat in the transfer press for 3-4 seconds after the foil carrier film has been removed.
IMPORTANT INFORMATION
For best durability of the foil after it is applied, it is recommended that the garment be hand washed or machine washed (delicate cycle) inside out and line or air dried. Do not use bleach. Do not iron printed area.



MULTI COLOR FOIL - Two or more colors with foil transfers can be accomplished one of two ways.

1st. Water Based or Discharge Inks. Foil only sticks to plastisol, so if you want foil to only stick to one part of the design, you can print foil adhesive or plastisol where you want the foil to transfer to and the rest of the design use water based or discharge inks. When transferred, foil will only stick to the plastisol area of the print.

2nd. Foil Resist Additive. Foil resist additive can be added into plastisol at around 15% per weight to resist the foil from adhering to the plastisol ink during the transfer process.


SPECIAL AFFECTS & FOIL - Foil can be transferred to a plethora of special affects inks. Depending on how the ink is printed, foil will stick to some or all of the design. It will work with puff, high density, granite base, blowout, suede, and more! Crumpling the foil also creates a cool effect. The point of foil is.

HAVE FUN AND EXPERIMENT. THERE ARE NO RULES!!!



Foil on High Density or Blowout Special Effects Ink